richard_crl032 Posted September 27, 2020 Share Posted September 27, 2020 54 minutes ago, JohnSwenson said: Hi Richard, my priority is quite different than yours: #1 geometry in order: star quad, twisted pair, zip cord #2 insulation material ie the dielectric. Teflon the best, polypropylene, silicone rubber, worst is PVC #3 gauge #3 metal type and purity Spend your money on the higher up on the list. In other words don't bother with silver or "6nines" until you already have teflon star quad. John S. Hi John, Thanks and understand but the impatient me could not wait .. just back from local audio contact quartz acoustic to reterminated one end of the stock UL1185 with the oyaide DC 2.5mm at usd25 to fit better (correctly) to my Bel Canto fm1 tuner. Will explore more from Ghentaudio on star quad gotham or canare ofc (latter preferred again for bigger diameter) which is affordable at usd48 just checked when upgrade itch returns For now, getting the used aka cheaper uptone lps1.2 to be powered by the redundant 7.5A output from the 60w x2 zerozone lps to power the Bel Canto and freeing the 12v used from the zerozone lps to the power my computer grade netgear switch instead of switching meanwell psu makes sense to me ... this dual lps yield more details and transparency with resulting clean background as well as knowing at least lps to the switch 😍. Cheers. Richard Revel Salon 2 speakers, Sander Magtech amp, Audible Illusion L3B (Blackgate) preamp, Denafrips Terminator Plus dac, Denafrips Hermes ddc, Antipodes CX/EX/P1/P2 server/player (Oladra upgraded), Denafrips Avatar cdp, Bel Canto fm1 tuner, Airties Wireless Mesh, ifi Blue Zen BT receiver, 2X Uptone EtherRegen + AfterDark Emperor Double Crown 10M clock, Zerozone 5/7.5/12v LPS, Uptone LPS 1.2, 2x diy 2kVA Isotransformers, dedicated 20/30A lines for separate digital/analog, Nordost Quattro Fil interconnects, Acoustic Revive TripleC Ethernet/i2S cables, Shunyata Sigma usb cable with ifi Idefender 3.0, Aurealis/Apogee/Canare BNC clock cables, Cardas Clear speaker cable and jumpers, Zonotone Shupreme/5050 powercords, Garrard 301 on slate plinth/sme 3012R/Ortofon Classic Royal GM mk2/diy 301 motor PSU/graham IC90/kimber tak ag etc./Headamp Gilmore Lite Mk2+Golden Reference PSU/Grado FreeSystem fg-1 headphones Link to comment
richard_crl032 Posted September 27, 2020 Share Posted September 27, 2020 13 hours ago, GryphonGuy said: You should definitely try the Gotham GAC-4/1 11301 UltraPro Star Quad DC(JSSG360) cable especially if you have an UltraCap LPS-1.2. The difference is amazing (in my system at least). Regards GG Hi GG, Got weak and ordered from Ghentaudio. Cheers. Richard Revel Salon 2 speakers, Sander Magtech amp, Audible Illusion L3B (Blackgate) preamp, Denafrips Terminator Plus dac, Denafrips Hermes ddc, Antipodes CX/EX/P1/P2 server/player (Oladra upgraded), Denafrips Avatar cdp, Bel Canto fm1 tuner, Airties Wireless Mesh, ifi Blue Zen BT receiver, 2X Uptone EtherRegen + AfterDark Emperor Double Crown 10M clock, Zerozone 5/7.5/12v LPS, Uptone LPS 1.2, 2x diy 2kVA Isotransformers, dedicated 20/30A lines for separate digital/analog, Nordost Quattro Fil interconnects, Acoustic Revive TripleC Ethernet/i2S cables, Shunyata Sigma usb cable with ifi Idefender 3.0, Aurealis/Apogee/Canare BNC clock cables, Cardas Clear speaker cable and jumpers, Zonotone Shupreme/5050 powercords, Garrard 301 on slate plinth/sme 3012R/Ortofon Classic Royal GM mk2/diy 301 motor PSU/graham IC90/kimber tak ag etc./Headamp Gilmore Lite Mk2+Golden Reference PSU/Grado FreeSystem fg-1 headphones Link to comment
tims Posted September 27, 2020 Share Posted September 27, 2020 12 hours ago, JohnSwenson said: Hi Richard, my priority is quite different than yours: #1 geometry in order: star quad, twisted pair, zip cord #2 insulation material ie the dielectric. Teflon the best, polypropylene, silicone rubber, worst is PVC #3 gauge #3 metal type and purity Spend your money on the higher up on the list. In other words don't bother with silver or "6nines" until you already have teflon star quad. John S. On 9/22/2020 at 7:17 PM, JohnSwenson said: Yep I'm still using them, I have found nothing better. I love them. By far the best cables I've ever had and WAY less money than other offerings. They DO take a long time to burn in. I just redid my phono system and replaced everything with the 1804A cables, phenomenal now. John S. Hi John With your 1804A RCA cables are you using any extra shielding such as the JSSG360 method? Thanks Link to comment
Popular Post JohnSwenson Posted September 28, 2020 Author Popular Post Share Posted September 28, 2020 8 hours ago, tims said: Hi John With your 1804A RCA cables are you using any extra shielding such as the JSSG360 method? Thanks I just use JSSG, otherwise known a use a silicon rubber wire to connect to the shield at both ends. I don't think the JSSG360 is particularly useful for audio cables, it does work for digital cables. John S. tims and R1200CL 2 Link to comment
Popular Post Nenon Posted September 28, 2020 Popular Post Share Posted September 28, 2020 21 hours ago, JohnSwenson said: Hi Richard, my priority is quite different than yours: #1 geometry in order: star quad, twisted pair, zip cord #2 insulation material ie the dielectric. Teflon the best, polypropylene, silicone rubber, worst is PVC #3 gauge #3 metal type and purity Spend your money on the higher up on the list. In other words don't bother with silver or "6nines" until you already have teflon star quad. John S. Hmmm, my priority is definitely different than that. At this point, I've received feedback from over 20 people who have done DC cables with the 15.5 AWG Mundorf silver/gold wire, and... with or without shielding... regardless of the geometry they used (some people twisted the wires, others just ran them parallel)... they sounded a lot better than anything else mentioned here. Significantly better, actually. In a good resolving system, replacing the DC cable with a Mundorf silver/gold cable could be as noticeable as replacing a component. The trick is to keep the cables short - 1-2 feet, no more than 3'. I am not trying to promote a product but just to spread some more awareness of this amazing wire. I've published a DIY recipe already, and anyone who can solder two wires can make them. Yes, the wire is expensive, but if you have a good audio system, it is totally worth it. genvirt and HumanMedia 1 1 Industry disclosure: Dealer for: Taiko Audio, Aries Cerat, Audio Mirror, Sean Jacobs https://chicagohifi.com Link to comment
richard_crl032 Posted September 28, 2020 Share Posted September 28, 2020 2 hours ago, Nenon said: Hmmm, my priority is definitely different than that. At this point, I've received feedback from over 20 people who have done DC cables with the 15.5 AWG Mundorf silver/gold wire, and... with or without shielding... regardless of the geometry they used (some people twisted the wires, others just ran them parallel)... they sounded a lot better than anything else mentioned here. Significantly better, actually. In a good resolving system, replacing the DC cable with a Mundorf silver/gold cable could be as noticeable as replacing a component. The trick is to keep the cables short - 1-2 feet, no more than 3'. I am not trying to promote a product but just to spread some more awareness of this amazing wire. I've published a DIY recipe already, and anyone who can solder two wires can make them. Yes, the wire is expensive, but if you have a good audio system, it is totally worth it. Hi Neon, I heard good things about this mundorf ag/au wire for dc cable locally also but mentioned twisted, straight up, with jssg360 etc. variants are unknown to me and surely that they also made differences for those who can hear "big" difference in the 1st place. Not too surprised also since awg15.5 at 1.46mm2 like stock compared to gotham, canare etc. especially if some diyers twist 2 strands into one. Any comment to these variants else I think many like me will hesitate to venture there. For me, I am a believer in cables at a price point used to tune one's system to their preference and its limitations but main improvement are from hardware itself and the technologies involved ... as in my case of adding secondary lps of uptone lps1.2 that yield favorable outcome for my bel canto fm1 tuner with quieter background that yield more details and transparency. Not a believer of wishful owners that a single cable as a minute part of one's system is as good as replacing a component at least generally and not a worse matching component .. else a joke to our hobby and advanced technologies to not needing the usd430 uptone lps1.2 and just add mundorf au/ag to my 1st level zerozone lps 🤪 Think I will stop with the Ghentaudio's gotham and perhaps at the risk of getting anal on this dc cable thingy but if you can help me to fabricate best mundorf au/ag variant of 0.5m with oyaide 2.1mm to 2.5mm, I will be interested to buy it from you and provide a review of any difference with stock terminated with oyaide 2.5mm and ghentaudio's gotham jssg360 in my not too bad resolution by speakers and headphone ... ymmv if course but test of the pudding at least for my ears then. Cheers. Richard Revel Salon 2 speakers, Sander Magtech amp, Audible Illusion L3B (Blackgate) preamp, Denafrips Terminator Plus dac, Denafrips Hermes ddc, Antipodes CX/EX/P1/P2 server/player (Oladra upgraded), Denafrips Avatar cdp, Bel Canto fm1 tuner, Airties Wireless Mesh, ifi Blue Zen BT receiver, 2X Uptone EtherRegen + AfterDark Emperor Double Crown 10M clock, Zerozone 5/7.5/12v LPS, Uptone LPS 1.2, 2x diy 2kVA Isotransformers, dedicated 20/30A lines for separate digital/analog, Nordost Quattro Fil interconnects, Acoustic Revive TripleC Ethernet/i2S cables, Shunyata Sigma usb cable with ifi Idefender 3.0, Aurealis/Apogee/Canare BNC clock cables, Cardas Clear speaker cable and jumpers, Zonotone Shupreme/5050 powercords, Garrard 301 on slate plinth/sme 3012R/Ortofon Classic Royal GM mk2/diy 301 motor PSU/graham IC90/kimber tak ag etc./Headamp Gilmore Lite Mk2+Golden Reference PSU/Grado FreeSystem fg-1 headphones Link to comment
asdf1000 Posted September 28, 2020 Share Posted September 28, 2020 7 hours ago, JohnSwenson said: I just use JSSG, otherwise known a use a silicon rubber wire to connect to the shield at both ends. I don't think the JSSG360 is particularly useful for audio cables, it does work for digital cables. John S. Hi John S, Just to clarify regarding the 1804A RCA cables with JSSG: the silicone wire connects to the shield at both ends , but the silicone wire and the shield both do NOT connect to the RCA plug at all, right? Link to comment
Popular Post Nenon Posted September 28, 2020 Popular Post Share Posted September 28, 2020 7 hours ago, richard_crl032 said: I heard good things about this mundorf ag/au wire for dc cable locally also but mentioned twisted, straight up, with jssg360 etc. variants are unknown to me and surely that they also made differences for those who can hear "big" difference in the 1st place. My point was that no matter what geometry you use with this wire (i.e. twisted or parallel wires), a cable with the 15.5 AWG Mundorf silver/gold wire sounds better than any other DC cable discussed here. At least to my years and in my system, but also to 20+ other people in their systems. Sure, the geometry and shielding makes a difference too. I did not say it did not. In fact, one of my first tests was with two identical cables but different shielding, one with JSSG360 and one without, connected to my cable modem. And yes, I could absolutely hear a difference. The fact that I could hear a difference of the shielding on a DC cable to my cable modem was quite shocking and an eye opener. I have tried both, twisted pair and parallel wires. My preference at the moment is to have the wires parallel, with the wires inserted inside an unbleached natural cotton sleeve. As for shielding, there are places where I like JSSG360 and places where I don't. However, as a starting point for people who want to try making this cable, I would recommend to do a twisted pair and JSSG360 shielding. Can't go wrong that way... 8 hours ago, richard_crl032 said: Not a believer of wishful owners that a single cable as a minute part of one's system is as good as replacing a component at least generally and not a worse matching component .. else a joke to our hobby and advanced technologies to not needing the usd430 uptone lps1.2 and just add mundorf au/ag to my 1st level zerozone lps Obviously some common sense should be applied when you read my posts, and it would be best if you can see from my point of view. I have a very resolving system and multiple very expensive power supplies. The more improvements I make to my system the more resolving it becomes, and the easier it is to hear small changes. If we go back in time two or three years, replacing my DAC had less of an impact than replacing the DC cable (e.g. feeding the JCAT XE USB card on my server) today. I am not suggesting that everyone would hear a difference between DC cables in any system. Most people won't, but those with very resolving systems would. Those with zerozone LPS may not hear very big difference with DC cables. And of course it would not be a good idea to spend more money on DC cables than the LPS. Upgrade the LPS first, and if you can hear clear differences between the Gotham, Neotech, and other DC cables mentioned here, maybe it's time to try a cable with the Mundorf silver/gold wire. Alchemist and richard_crl032 1 1 Industry disclosure: Dealer for: Taiko Audio, Aries Cerat, Audio Mirror, Sean Jacobs https://chicagohifi.com Link to comment
richard_crl032 Posted September 28, 2020 Share Posted September 28, 2020 1 hour ago, Nenon said: My point was that no matter what geometry you use with this wire (i.e. twisted or parallel wires), a cable with the 15.5 AWG Mundorf silver/gold wire sounds better than any other DC cable discussed here. At least to my years and in my system, but also to 20+ other people in their systems. Sure, the geometry and shielding makes a difference too. I did not say it did not. In fact, one of my first tests was with two identical cables but different shielding, one with JSSG360 and one without, connected to my cable modem. And yes, I could absolutely hear a difference. The fact that I could hear a difference of the shielding on a DC cable to my cable modem was quite shocking and an eye opener. I have tried both, twisted pair and parallel wires. My preference at the moment is to have the wires parallel, with the wires inserted inside an unbleached natural cotton sleeve. As for shielding, there are places where I like JSSG360 and places where I don't. However, as a starting point for people who want to try making this cable, I would recommend to do a twisted pair and JSSG360 shielding. Can't go wrong that way... Obviously some common sense should be applied when you read my posts, and it would be best if you can see from my point of view. I have a very resolving system and multiple very expensive power supplies. The more improvements I make to my system the more resolving it becomes, and the easier it is to hear small changes. If we go back in time two or three years, replacing my DAC had less of an impact than replacing the DC cable (e.g. feeding the JCAT XE USB card on my server) today. I am not suggesting that everyone would hear a difference between DC cables in any system. Most people won't, but those with very resolving systems would. Those with zerozone LPS may not hear very big difference with DC cables. And of course it would not be a good idea to spend more money on DC cables than the LPS. Upgrade the LPS first, and if you can hear clear differences between the Gotham, Neotech, and other DC cables mentioned here, maybe it's time to try a cable with the Mundorf silver/gold wire. Hi Neon, Thanks for the sharing on the mundorf au/ag dc cable variants if one wish to diy .. perhaps later but still no confidence to do it well or needed as yet. Sorry for not being clear .. the zerozone lps 7.5v is powering the uptone lps1.2 and the dc cable is to replace the stock awg16 of uptone for 12v .. will share if indeed any difference upon receipt of Ghent's gotham from stock terminated one end with Oyaide 2.5mm dc connector for my Bel Canto. Not sure what lps meets your requirement of a discerning lps but uptone lps1.2 ok ? Btw, zerozone is based on below just in case and hope these amb guys knows what they are doing then: https://www.amb.org/audio/sigma22/ Meanwhile, indeed it irks me to see statements by cables owners who believe their latest cable remotely equals to change to better equipment .. regardless their passion and often in hardball manners. You may also want to share your system setup for us to understand your lps, sources dac, speakers/headphone etc. and where the mundorf ag/au dc cable is used to understand the mentioned high resolution needed to discern the big improvement. Cheers Richard Revel Salon 2 speakers, Sander Magtech amp, Audible Illusion L3B (Blackgate) preamp, Denafrips Terminator Plus dac, Denafrips Hermes ddc, Antipodes CX/EX/P1/P2 server/player (Oladra upgraded), Denafrips Avatar cdp, Bel Canto fm1 tuner, Airties Wireless Mesh, ifi Blue Zen BT receiver, 2X Uptone EtherRegen + AfterDark Emperor Double Crown 10M clock, Zerozone 5/7.5/12v LPS, Uptone LPS 1.2, 2x diy 2kVA Isotransformers, dedicated 20/30A lines for separate digital/analog, Nordost Quattro Fil interconnects, Acoustic Revive TripleC Ethernet/i2S cables, Shunyata Sigma usb cable with ifi Idefender 3.0, Aurealis/Apogee/Canare BNC clock cables, Cardas Clear speaker cable and jumpers, Zonotone Shupreme/5050 powercords, Garrard 301 on slate plinth/sme 3012R/Ortofon Classic Royal GM mk2/diy 301 motor PSU/graham IC90/kimber tak ag etc./Headamp Gilmore Lite Mk2+Golden Reference PSU/Grado FreeSystem fg-1 headphones Link to comment
Popular Post Nenon Posted September 28, 2020 Popular Post Share Posted September 28, 2020 1 hour ago, richard_crl032 said: Hi Neon, Thanks for the sharing on the mundorf au/ag dc cable variants if one wish to diy .. perhaps later but still no confidence to do it well or needed as yet. Sorry for not being clear .. the zerozone lps 7.5v is powering the uptone lps1.2 and the dc cable is to replace the stock awg16 of uptone for 12v .. will share if indeed any difference upon receipt of Ghent's gotham from stock terminated one end with Oyaide 2.5mm dc connector for my Bel Canto. Not sure what lps meets your requirement of a discerning lps but uptone lps1.2 ok ? Btw, zerozone is based on below just in case and hope these amb guys knows what they are doing then: https://www.amb.org/audio/sigma22/ Meanwhile, indeed it irks me to see statements by cables owners who believe their latest cable remotely equals to change to better equipment .. regardless their passion and often in hardball manners. You may also want to share your system setup for us to understand your lps, sources dac, speakers/headphone etc. and where the mundorf ag/au dc cable is used to understand the mentioned high resolution needed to discern the big improvement. Cheers Richard @richard_crl032 - With all good feelings and nothing negative, let me say that I really wish you get to the point where replacing a DC cable is as enjoyable as replacing a component. It's much more fun compared to the state of 1 hour ago, richard_crl032 said: Meanwhile, indeed it irks me to see statements by cables owners who believe their latest cable remotely equals to change to better equipment .. regardless their passion and often in hardball manners. I can probably dig out some comments I've made years ago to people who claimed how big of a difference cables made in their system. It was really pissing me off to be honest. I could not hear differences between cables in my system and their comments were really annoying to me! And now I am one of those guys... Same goes about switches and a few other components that look and smell like snake oil from far away until you dive deeper into the subject and start listening on a resolving system. But my intention was not to start a debate. I just wanted to spread awareness for open minded people who can hear the difference and can try making their own DC cables. It is annoying to see a $10,000 cable with materials for $500, and I want to see more people building their own. 1 hour ago, richard_crl032 said: You may also want to share your system setup for us to understand your lps, sources dac, speakers/headphone etc. and where the mundorf ag/au dc cable is used to understand the mentioned high resolution needed to discern the big improvement. Sure, but it's a little difficult. The only off the shelf components I use is my recently acquired SoundApplication TT-7 power conditioner and my turntable/tonearm/cartridge/minusK stand. Everything else is custom built or DIY. My server is a DIY version of the Taiko Extreme server with some additions like the JCAT XE card, and with different power supply, chassis, RAM, etc. But it has a lot of similarities. And this is where DC cables make a big difference. My DAC is DIY I have been working on for several years. It's highly tweaked for my system/room/tastes and uses 6 rails of high quality LPS for the digital section and 2 for the analog. It's a NOS DAC with tube-based analog section. Took forever to find the best transformers for I/V conversion and all the other parts that went into that build. It's a one off that would never be seen in production. Line stage is a custom version of the Don Sach SP14. I just used better chassis and components. I am bi-amping with four SET monoblocks, some details here: On 6/9/2020 at 11:29 AM, Nenon said: 1. I completed my tube SET monoblocks a couple of weeks ago. They sound amazing! Even better than they look. The Duelund Cast tinned copper caps are still breaking-in as well as all the Mundorf MTube and MLytic AG capacitors I used but they are 99% there. Add to that, the custom silver wires used throughout, Mundorf silver/gold wire for the power supply, custom transformers, custom chokes, Z-foil resistors, WBT silver connectors, NCF IEC inlets, Grade A Sophia Electric tubes, Grade A Shuguang WE6SN7 PLUS tubes, SR Orange fuses, etc. I used to love my Lundahl output transformers but those beat the shit out of the Lundahls! These monoblocks are something special. They really are a piece of art, and I am very proud of the end result. Sorry for the ugly photo, but that's the best I have at the moment. Speakers details: On 6/9/2020 at 2:45 PM, Nenon said: I built The Loudspeaker (TL-1) by Troels Gravesen about 18 months ago, and that has been my reference since then. Needless to say, I went overboard with my OCD. They also use Duelund tinned copper caps as well as Jantzen Amber-Z Caps, Path Audio resistors (not a fan of the Duelund resistors), special wire, WBT connectors, top quality 1.5'' thick baltic birch, etc. They have 18'' woofers. The original design was using DSP and ClassD Hypex plate amps for the 18'' woofers, but I am very sensitive on bass details and definition. After a lot of testing, I settled on passive crossovers and bi-amping. Tried quite a few amplification options, including the Jeff Rowland 625 S2 amps as mentioned in one of my previous posts. But when I heard what those AudioMirror monoblocks did, I could not go back to anything else. That was not a self-intuitive test result. Typically one of the weaknesses of tube amplification is deep base. But I guess 95dB efficient 18'' woofers are a different beast. So, here I am, bi-amping with two sets of monoblocks (4 monoblocks total)!!! The question is what am I going to do in the summer months with those heaters... it was nice and cozy in the winter :). I won't disclose power supplies, because this forum is about Uptone Audio. I am a proud owner of some Uptone products including the LPS-1.2 and etherREGEN. And I have a lot of respect for Alex and John! Going back to DC cables and the Mundorf silver/gold wire - here is an interesting read: On 2/16/2020 at 5:49 AM, Blackmorec said: Well this has been an excellent week for me regarding matters audio, both thanks to this forum. I was introduced to the music and artistry of Anoushka Shankar and I tried a pair of Mundorf Silver Gold DC cables (NMSGs) very kindly built and supplied by Nenon. For the past 30 or more years, an argument has raged between objectivists and subjectivists about the degree to which cables can impact sound quality. The argument was already hot during the late Analog era, but the advent of digital data streams added more coal to the fire. How can a cable possibly affect a bit stream, especially one that is filtered and retimed downstream of the cable, resulting in a so-called bit-perfect stream arriving at the DAC? Well unfortunately I don’t have that particular answer and all I have is yet more anecdotal evidence that cables do indeed have an effect of SQ. Objectivists may claim that confirmation bias is responsible and I will admit to being positively disposed to these NMSG cables. So if you think that conformation bias is what’s responsible for what I hear, that’s fine by me, but for those who’ve proven for themselves that cables make a difference, read on. Nenon has already described in detail how his DC cables are built, which are essentially a JSSG360 screened twisted pair of Mundorf Silver Gold wires with Oyaide plugs to order. I have already described my system, but for completeness, it comprises a highly optimised network based on a dedicated 500Mbps 5GHz wi-fi band, Sean Jacob’s DC3s LPSs and Synergistic Research Atmosphere X ethernet cables throughout, feeding an Innuos Statement and Devialet 440 Expert Pro CI DAC and amps. The network is essentially ethernet cables with wi-fi isolation between the dedicated router and hi-fi room. My system employs 4 DC3 LPSs, so 4 DC cables....DC3 to Modem and Router are Sean Jacob’s extremely competent twisted pair with ferrite filter while the DC3 to TPLink RE650 wi-fi receiver/ethernet and DC3 to AQVox SE were recently upgraded from Sean Jacob’s cables to a pair of Ghent Audio Neotech JSSG360 7N UPOCC cables. In its initial state with 4 SJ cables handling the network’s DC, my system sounded awesome....tick all the hi-fi boxes of extended shimmering tremble and deep mellifluous bass, soundstage based entirely on the recording venue and its ambient clues. There was nothing about the sound I didn’t like. PRaT was SOTA, timing was exquisite, detail sounded ‘complete’, clarity and purity were reference level and listener involvement was of the highest order. In other words there were no sonic problems to solve and the music was entirely thrilling or moving, depending on genre. Initially I also had a rather competent analog front end, but this digital system eventually trounced the analog set-up so thoroughly that it got traded, no longer worth the fuss and bother of playing LPs. As I discuss these new DC cables, the first very valid question must be of course; ‘how much can 2 DC cables powering upstream network components actually affect sound quality?” Intuitively I and probably most of you would likely believe “not much”, but that is absolutely not my experience. In fact, “a great deal” is far closer to what I hear. Why? No idea, other than the fact that the digital stream is in fact modulated DC so any DC characteristics that do contribute to sound quality will likely make it through the stream, along with the timed bits. So let’s discuss the NMSGs. The cables are solid core, beautifully easy to form and hold their shape 100%. There is no springiness at all so its just a matter of smoothly bending them to fit the exact installation requirements, curving smoothly around other cables and orientating the plugs perfectly, with no strain. LIke all cables, I have noticed some running-in anomalies. I normally listen to my system at a volume setting of -14.5dB. With the new NMSGs I need to increase that to -9dB to achieve the same SPL. Some may say its lower noise and distortion that means I can listen louder, but that’s not what’s happening. I noticed exactly the same thing with the Neotechs...the missing 5dB returning after about 2 weeks of being constantly powered up. I also notice a slight attenuation of dynamics and perhaps slightly less treble shimmer and sparkle....I’m pretty certain that like the Neotechs, this will all return in due course. Running-in deficits not withstanding, the NMSGs significantly outperformed the Neotechs although I can’t really report any typical audiophile improvements..... frequency extremes were already extended and rich in timbral detail, soundstage was, as mentioned, as big or small as what is on the recording, there is NO listening room identity, only the recorded venue and music is 3 dimensional, and sounds like its being played by the instruments....so from an Audiophile perspective, not much room for improvement. However there were some major improvements, just that they related entirely to the music rather than to its presentation. The first thing you notice is that the music gains in finesse, inner detail, inner warmth, ease and ‘humanness’. Things like mouth and breath sounds became a lot more complex, detailed and real. The music is mesmerising, almost hypnotically so, sending shivers of pleasure down your spine. The harp in Andreas Vollenweider’s Cosmology sounded lively, vibrant and sparkling, with gorgeous decay, that extends down into complete silence....what makes this all the more amazing is that you can sense the silence even while other instruments are playing. The system seems to have far greater, finely delineated spacial resolution, which makes the soundstage all the more engaging, precise (not etched) and clear, so you can easily follow 2 or more closely related instruments by virtue of their spacial differentiation. This is especially important when sounds differ markedly in amplitude....loud sounds don’t swamp quiet sounds because they are positioned differently in space so don’t interfere. When you increase spacial resolution you hear more low level detail and greater low level detail creates a greater feeling of reality as sounds are revealed that you would normally only hear live. The soundstage itself is also affected. Lower noise and greater low level detail give the entire sound stage a presence, a shape, texture, dimensions, even when there are no instruments playing....the size and shape of the recording venue becomes easier to hear...there’s atmosphere and air ....space that has a presence...an ‘eyes closed’ illusion that you’re sitting listening in an entirely different space with no relation whatsoever to your room. The music itself has greater bounce and buoyancy.....with more shape and body to the instruments. Instruments positions are very precisely defined in terms of depth and height within the soundstage. Again this makes individual instruments far clearer in the mix, without any analytical characteristics. With the NMSG cables, the music has an inner glow and a richness. The music sounds like it is energising the venue....grand piano for example can have a beautiful percussive hammer strike, after which the music blooms out and expands to energise the room, before decaying according to how long the sustain pedal is held. Timbral detail (tone and texture) has always been excellent but with the NMSGs it now remains stable and present down to absolute silence. That soesn’t sound like a big deal, but it again makes things sound more realistic. Rhythmic flow often feels like a strong undercurrent, subtle but powerful and irresistible, pulling you along with it. Instruments sound beautifully consolidated, woven together to form a glorious whole. Even when they’re only subtly involved in the mix, their contribution can be powerfully intoxicating. Then there’s the music’s ability to generate feelings. We often speak about emotions, but this goes well beyond that as the feelings are unique to the music....the music changes how you feel, and how you feel changes how you hear the music.....amplifying its atmosphere and your reaction to it. Take for example Malia’s Celestial Echo. Extremely atmospheric, extended bass with beautiful warmth, tremendous finesse....very pure, very precise, beautifully timed. The bass is round and bounces from note to note.Tomtoms ‘pop’ with dynamic accuracy, even when played quietly. The system creates acoustics that literally play with your mind, making you feel spaced out, because that’s precisely what you’re hearing and experiencing in your ‘head space’ In my system at least, the NMSG cables make the music live and breathe....they bring the music to life. Songs I wasn’t that fond of suddenly blow my mind with their detail, depth and presence. The spatial precision results in improved clarity, purity and the fundamental rightness of the sound. The music creates an atmosphere, which generates feelings that you ‘hear the music through’. For example the music may make you feel spiritual and other worldly, so your feelings reinforce the music....which is why the listener involvement is so incredibly high....the music and your inner feelings become inextricably linked. I hope I’m explaining this clearly? Last week I was introduced to Anoushka Shankar’s album Rise. The music, predominantly Sitar, Voice and Pecussion sounds exotic, eastern and literally soaking in spiritual essence. It is beautifully resonant with super long note decay. The music is highly atmospheric....with some tracks having a rhythmic undertow of riptide proportions . On one track the musician playing tabla percussion sounds like he’s only five or six feet away from the listening chair......its not loud, but includes all the clues to make the music extremely ‘present’ and intimate. The music and instruments suit each other perfectly and the pace of the music and development of the Sitar’s notes are so beautifully coordinated they’ll bring tears of joy at their sheer beauty. Another album that demonstrates the NMSG’s prowess is Jan Garbarek’s Legend of the 7 Dreams. Voy Contando is spacious, airy, hauntingly beautiful. There’s a simple drum beat.....but what makes it very special is the astounding clarity and complexity. The system weaves magical spells in the air, with instruments floating in huge spaces that always puts me in mind of northern larch forests and huge open, cold and lonely wilderness. At some time I’ve got to stop upgrading my system and instead just enjoy fully what I have. I sense that time may be just around the corner. Nenon is kindly making 2 more cables for my Modem and Router. With the right recordings my system can already present the music in a way that rocks or moves every fibre of my being, takes over my consciousness and creates my mood. More than that I don’t need. What I find truly amazing about this is that this final touch, the last step that convinces me that I’ve reached the place I want to be sonically, is brought about by 2 DC cables. Even I can sympathize with the objectivists who would poopoo such subjective nonsense....how do 2 DC cables add the atmosphere, the finesse and the beauty that I’m reporting here? So 5 days in and 2 more cables on the way we’ll see where this leads...suffice to say, if you’re pursuing audio perfection and you’re able to solder competently, you should make at least one of Nenons NMSG cables. I’m pretty certain you’ll very much like what it brings. Finally, to close this initial assessment a big thank you to Nenon who went to a lot of trouble to buy, build and ship these cables for me to try. They are certainly a surprisingly key component in reaching my own personal sonic nirvana. As much as I like to be engaged in audio discussions, debates about cables are absolutely meaningless to me. And I won't engage in such. I hope I made the point I was trying to convey. Cheers. Superdad, jean-michel6, Gavin1977 and 4 others 1 3 3 Industry disclosure: Dealer for: Taiko Audio, Aries Cerat, Audio Mirror, Sean Jacobs https://chicagohifi.com Link to comment
richard_crl032 Posted September 28, 2020 Share Posted September 28, 2020 Hi Neon, Noted and thanks again ! All good and hope to get mundorf au/ag cable to mod one of the dc cable some day to know the difference albiet not expecting anything like in your setup as it is only for my bel canto fm1 tuner. Cheers. Richard Nenon 1 Revel Salon 2 speakers, Sander Magtech amp, Audible Illusion L3B (Blackgate) preamp, Denafrips Terminator Plus dac, Denafrips Hermes ddc, Antipodes CX/EX/P1/P2 server/player (Oladra upgraded), Denafrips Avatar cdp, Bel Canto fm1 tuner, Airties Wireless Mesh, ifi Blue Zen BT receiver, 2X Uptone EtherRegen + AfterDark Emperor Double Crown 10M clock, Zerozone 5/7.5/12v LPS, Uptone LPS 1.2, 2x diy 2kVA Isotransformers, dedicated 20/30A lines for separate digital/analog, Nordost Quattro Fil interconnects, Acoustic Revive TripleC Ethernet/i2S cables, Shunyata Sigma usb cable with ifi Idefender 3.0, Aurealis/Apogee/Canare BNC clock cables, Cardas Clear speaker cable and jumpers, Zonotone Shupreme/5050 powercords, Garrard 301 on slate plinth/sme 3012R/Ortofon Classic Royal GM mk2/diy 301 motor PSU/graham IC90/kimber tak ag etc./Headamp Gilmore Lite Mk2+Golden Reference PSU/Grado FreeSystem fg-1 headphones Link to comment
tims Posted September 29, 2020 Share Posted September 29, 2020 On 9/29/2020 at 3:53 AM, Nenon said: My point was that no matter what geometry you use with this wire (i.e. twisted or parallel wires), a cable with the 15.5 AWG Mundorf silver/gold wire sounds better than any other DC cable discussed here. At least to my years and in my system, but also to 20+ other people in their systems. Sure, the geometry and shielding makes a difference too. I did not say it did not. In fact, one of my first tests was with two identical cables but different shielding, one with JSSG360 and one without, connected to my cable modem. And yes, I could absolutely hear a difference. The fact that I could hear a difference of the shielding on a DC cable to my cable modem was quite shocking and an eye opener. I have tried both, twisted pair and parallel wires. My preference at the moment is to have the wires parallel, with the wires inserted inside an unbleached natural cotton sleeve. As for shielding, there are places where I like JSSG360 and places where I don't. However, as a starting point for people who want to try making this cable, I would recommend to do a twisted pair and JSSG360 shielding. Can't go wrong that way... Obviously some common sense should be applied when you read my posts, and it would be best if you can see from my point of view. I have a very resolving system and multiple very expensive power supplies. The more improvements I make to my system the more resolving it becomes, and the easier it is to hear small changes. If we go back in time two or three years, replacing my DAC had less of an impact than replacing the DC cable (e.g. feeding the JCAT XE USB card on my server) today. I am not suggesting that everyone would hear a difference between DC cables in any system. Most people won't, but those with very resolving systems would. Those with zerozone LPS may not hear very big difference with DC cables. And of course it would not be a good idea to spend more money on DC cables than the LPS. Upgrade the LPS first, and if you can hear clear differences between the Gotham, Neotech, and other DC cables mentioned here, maybe it's time to try a cable with the Mundorf silver/gold wire. Hi Nenon In regard to the mundorf wire, how do you think it would suit using it in a diy star quad design? The reason I ask is that I seen the wire in the past and it seemed to me at the time to be rigid and not very flexible and I wonder how the insulation (on the wire) would stand up to the tight twisting required for the star quad design? OT but any ideas if the mundorf wire would make a difference in say a diy RCA cable? I'm thinking of this design here: https://www.venhaus1.com/diysilverinterconnects.html Maybe the minute signal current involved would negate any benefit the mundorf would give; don't know :) Link to comment
Nenon Posted September 29, 2020 Share Posted September 29, 2020 2 minutes ago, tims said: In regard to the mundorf wire, how do you think it would suit using it in a diy star quad design? The reason I ask is that I seen the wire in the past and it seemed to me at the time to be rigid and not very flexible and I wonder how the insulation (on the wire) would stand up to the tight twisting required for the star quad design? I think it would work fine. 2 minutes ago, tims said: OT but any ideas if the mundorf wire would make a difference in say a diy RCA cable? Never tried that to be honest. Industry disclosure: Dealer for: Taiko Audio, Aries Cerat, Audio Mirror, Sean Jacobs https://chicagohifi.com Link to comment
lmitche Posted September 29, 2020 Share Posted September 29, 2020 LOL, Shall we start the "Less than $45/Foot DIY DC power cables" thread or can some one create the "Greater than $45 /foot DIY DC power cables" thread? More than $10 a foot suppresses my participation. This saddens me as I kinda enjoyed this thread in the past. 😅 Pareto Audio aka nuckleheadaudio Link to comment
Ricardo007 Posted October 3, 2020 Share Posted October 3, 2020 On 9/28/2020 at 6:06 AM, Nenon said: they sounded a lot better than anything else mentioned here Hi Nenon, Have you tried them on the master clock or on a buffalo switch power supply? regards Richard Link to comment
Ricardo007 Posted October 10, 2020 Share Posted October 10, 2020 Topic on Lessloss bulk wires: I want to use these cables to make DC cable with oyaide DC barrel connectors Any suggestions how how to do that ? The lessloss wire is interesting because of its geometry, cotton as dielectric (no plastic), awg of the 192 strands is 13-14 awg, cotton fiber also used inside to damp microvibrations. I plan to use the already tinned version ready to solder since I dont have a soldering pot. My intent is to use one wire for the + and one for the ground in parrallel (difficult to twist if at the other end appears a difference of length). Do you think it can fit into the oyaide and what is best way to manage that (with WBT copper sleeve?). I plan to use an outside jacket carbon infused nylon by techflex : https://www.techflex.com/metal-shielding/flexo-anti-stat?product_selected=CNN0.25BK thanks for experienced DIYers to chime in! Richard Link to comment
pl_svn Posted October 10, 2020 Share Posted October 10, 2020 11 minutes ago, Ricardo007 said: I plan to use the already tinned version ready to solder since I dont have a soldering pot you must solder if you plan using those Oyaide DC plugs Qnap HS-264 NAS (powered by an HD-Plex 100w LPS) > Cirrus7 Nimbini v2.5 Media Edition i7-8559U/32/512 running Roon ROCK (powered by a Keces P8 LPS) > Lumin U2 > Metrum Acoustics Adagio NOS digital preamplifier > Metrum Acoustics Forte power amplifier (or First Watt SIT 3 power amplifier or Don Garber Fi "Y" 6922 tube preamplifier + Don Garber Fi "X" 2A3 SET power amplifier, both powered from an Alpha-Core BP-30 Isolated Symmetrical Power Transformer) > Klipsch Cornwall IV headphones system: Cirrus 7 > Lumin U2 > Metrum Acoustics Adagio > Pathos Aurium amplifier (powered by an UpTone Audio JS-2 LPS) > Focal Clear headphones Link to comment
Ricardo007 Posted October 10, 2020 Share Posted October 10, 2020 yes i know... Those are litz wires i dont have soldering pot to remove isolant , fuse the wires and tin them, so i will buy them already prepared redy to solder with a simple iron pl_svn 1 Link to comment
Roasty Posted October 19, 2020 Share Posted October 19, 2020 I am using a few Farad Super 3 power supplies, paired with some Gotham dc cables from Ghent Audio. Have been wondering about the Farad level 2 silver dc cables. Recently spoke to a forum member here and he was recommending the mundorf silver/gold, and gave some useful local contacts to have them made. Has anyone compared the Farad silver dc to the mundorfs? I don't have very good experience with silver/gold combination (I assume there is both silver and gold in the wire build, given the name); I had a silver/gold headphone cable made a while back and it was a bit of a disappointment in that there was loss of dynamism and very rolled off highs resulting in lack of clarity and sparkle. Also there was lack of low end extension. So just a little bit concerned, before I set off on an expedition to get several new dc cables made/ordered.. Link to comment
Ricardo007 Posted October 19, 2020 Share Posted October 19, 2020 2 hours ago, Roasty said: I am using a few Farad Super 3 power supplies, paired with some Gotham dc cables from Ghent Audio. Have been wondering about the Farad level 2 silver dc cables. Recently spoke to a forum member here and he was recommending the mundorf silver/gold, and gave some useful local contacts to have them made. Has anyone compared the Farad silver dc to the mundorfs? I don't have very good experience with silver/gold combination (I assume there is both silver and gold in the wire build, given the name); I had a silver/gold headphone cable made a while back and it was a bit of a disappointment in that there was loss of dynamism and very rolled off highs resulting in lack of clarity and sparkle. Also there was lack of low end extension. So just a little bit concerned, before I set off on an expedition to get several new dc cables made/ordered.. first thing is to determine how you handle the GX16 side of things, it is a 4 pin connector, are you planning to use 4 wires? in that case you cannot use 4 mundorf on the oyaide side. central pin of oyaide is 1.8mm internal diameter and mundorf is 15.5 awg, so I dont think you can put 2 mundorf wires on the central pin of oyaide, do you? alternatively you can use only 2 mundorf but you have to check the internal diameter of GX16 connector, i dont know... Farad uses 4x2 wires of 26 awg in its silver version so it gives you 20awg for the + Link to comment
Roasty Posted October 19, 2020 Share Posted October 19, 2020 53 minutes ago, Ricardo007 said: first thing is to determine how you handle the GX16 side of things, it is a 4 pin connector, are you planning to use 4 wires? in that case you cannot use 4 mundorf on the oyaide side. central pin of oyaide is 1.8mm internal diameter and mundorf is 15.5 awg, so I dont think you can put 2 mundorf wires on the central pin of oyaide, do you? alternatively you can use only 2 mundorf but you have to check the internal diameter of GX16 connector, i dont know... Farad uses 4x2 wires of 26 awg in its silver version so it gives you 20awg for the + From what was communicated to me, 2x 18awg into stock farad GX16 for each cable. He has gotten these made successfully. I have no experience in cable DIY so I will likely just follow whatever is recommended. Link to comment
Ricardo007 Posted October 19, 2020 Share Posted October 19, 2020 15 minutes ago, Roasty said: From what was communicated to me, 2x 18awg into stock farad GX16 for each cable. He has gotten these made successfully. I have no experience in cable DIY so I will likely just follow whatever is recommended. who is he? Link to comment
Roasty Posted October 19, 2020 Share Posted October 19, 2020 Just now, Ricardo007 said: who is he? I believe his forum nick is abyssman. Link to comment
HumanMedia Posted October 27, 2020 Share Posted October 27, 2020 i have also heard good things about the Mundorf Silver Gold. I am in the same boat as you @Roasty, in that I want to DIY a DC cable for the Farad3, with its GX16. I have the GX16 connectors but I have been trying to figure out how to get it to fit. My inclination is as you have indicated, use 4 stands of 18AWG in a star quad twist and hopefully fit it into a Oyaide DC barrel. So it is possible!? Have you tried this @Nenon? Are there any downsides? And can you link to your Mundorf DC cable recipe? Other comments- I had two Gotham JSSG360 cables made and they proved to have an annoying treble over time, and neither are in my system anymore, it was a relief to have them out. I also didn’t like the Neotech, for me it was slow and plodding sounding. I actually prefer the cheaper Canare 4S8 which has the bass of the Neotech but is quicker and more agile sounding. Anyway, any comments, guidance or experience with 18 AwG Mundorf silver gold into the Oyaide barrell would be hugely appreciated. Link to comment
charlesphoto Posted October 27, 2020 Share Posted October 27, 2020 You can always leave the barrel of the Oyaide off and fashion some other type of strain relief using a barrel of some sort and plenty of heat shrink. Won't look pretty but would work. Might be best with the angle plug as that gives a nice solid body to grasp. SERVER CLOSET (in office directly below living room stereo):NUC 7i5BNH with Roon ROCK (ZeroZone 12V on the NUC)>Cisco 2690L-16PS switch>Sonore opticalModule (Uptone LPS 1.2)> LIVING ROOM: Sonore opticalRendu Roon version (Sonore Power Supply)> Shunyata Venom USB>Naim DAC V1>Witchhat DIN>Naim NAP 160 Bolt Down>Chord Rumor 2>Audio Physic Compact Classics. OFFICE: opticalModule> Sonore microRendu 1.4> Matrix Mini-i Pro 3> Naim NAP 110>NACA5>KEF Ls50's. BJC 6a and Ghent Catsnake 6a JSSG ethernet; AC cables: Shunyata Venom NR V-10; Audience Forte F3; Ice Age copper/copper; Sean Jacobs CHC PowerBlack, Moon Audio DIN>RCA, USB A>C. Isolation: Herbie's Audio Lab. Link to comment
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now