AfterDark. Posted September 23, 2021 Share Posted September 23, 2021 The development of DELA S100 Network Hubs x Giesemann OCXO Black Modernize Edition With the development of D100, DELA developed Audioohile Network Hubs. It fully meets the requirements to ensure the quality of Network Streaming. It takes the function of the DELA series to a new level. For example, using SFP as a high-end network switch, supporting optical fiber technology to transmit signals. Purchase Link The chassis of DELA S100 adopts a sandwich type shock-absorbing structure, and the top and bottom plates are reinforced with aluminum plates to improve stability. And built-in high-quality clock circuit, so that the time base error is further reduced. The power supply part adopts large-capacity capacitor technology to ensure stable and pure voltage. All made in Japan. How we design a modified DELA S100? Improve the outlook which make it more like a audiophile gear The device should be powered externally with audiophile grade LPS The power section should be enhanced with more exotic audio capacitors The Giesemann OCXO 25Mhz will be optimised to DELA S100. The Giesemann Clock will be in module, to supply the cleanest clock signal to the board. The OCXO version should be fit into one single box for DELA S100 The internal wire with optimised with Duelund Silver Cable, and solder with Audio Note The chassis will be using Carbon Fiber to tailor made to place at the top of DELA S100. The use of SFP Single Mode Optical Fiber will give you another isolation to connect Cascade of DELA S100 The EMI shielding from KAMET corp. will apply to the RJ45 ports Enhancement on Industrial Grade Thermal material from Shin-Etsu (Made in Japan) will apply to CPU again. DELA S100 Black SE Edition Black Modernize Full Upgrade: Audio Capacitor upgrade to Frolyt (Used by Goldmund) (Made in Germany) Replace the DC cable inside with Duelund Audio Cables. AfterDark. Carbon Fiber AudiophileMAT Shielding 3M EMI Shielding apply on each Lan Ports / CPU / RAM AfterDark. Project ClayX Giesemann Linear Power Supply at 12V (External) Upgrade Capacitor to Audio Grade Bioplar FROLYT Capacitor (Made in Germany) for optimal sounding (Goldmund used this special capacitor for sound tuning on Preamplifier and their Phono amplififier) Why mixture of Exotic FROLYT Audio Capacitor? Frolyt ERY Series 4700uF x 3 = Total 14100uF Frolyt Bioplar EKSU Series 470uF x 2 = Total 940uF Compared to orignal, Mix of Flolyt will improve the micro details and dynamic of music, more natural and laid back To usd of exceesive and oversize of Audio Capacitor will remove the bottleneck and imcrease smoothess of music flows Why do we choose managed Network Hubs? Customerisation on VLAN, Subnet, Flow Control and QoS can lower the latancy on each lan ports. The sounding can be configured and optimised to Audiophiles. The internal cable is replaced with Dueland Audio Cable. As you see their is extra Capacitor section compared with the Buffalo GS-BS2016. We replaced the Japan capacitor with larger Floyt Audio Capacitor from Germany. The LED light can be switch off by Audiophiles, it can reduce the electric noise and darkness at the background will be increased. We can now confirm the motherboard of DELA S100 is the same as Buffalo GS-BS2016. Someone may noticed that the DELA S100 is only with 8 ports, which is different to Buffalo GS-BS2016 having 16 ports. Actually DELA S100 actually hide the top 8 ports nicely with the back plate and was disabled those port in admin page. The LED can be switch off to eliminate noises. The DELA S100 has external DC port which allow customer to use their Linear Power Supply (LPS) to power them in 12V 1A So we are quite excited to open up the large heat sink and have a look what is inside. The inside is opened, both Buffalo GS-BS2016 and DELA S100 is using BROADCOM BCM53343A, the internal clock is near the silver Broadcom. The excessive size of Aluminium heat sink is good to work 24x7 in commercial. As you may know, the lower the heat, the music representation will be more relax and laid back. The rich representation on sounding and lush airly high may be due to proper sofware implementation and high specification on motherboard, and using a very low jitter re-clock high performance switch with BROADCOM BCM53343A. All internal DC Cables is upgraded to Duelund Audio Cables AfterDark. Project ClayX Carbon Fiber AudiophileMAT Shielding AfterDark. Giesemann OCXO Master Clock Features: The product uses the selected audio grade OCXO, and through long-term calibration to select and install equipment with excellent stability. OCXO that employs with qualitative measure equipment. OCXO is enclosed and covered with Dynamat Extreme Corporation (Made in USA) which is used to stabilize and minimize heat separation, addition EMI material from KEMET EMI Shielding is placed on top of OCXO, the outer layer is covered with real leather to isolate the heat factors for maximizing OCXO performance . Advanced instrument Symmetricom 5125A calibrated with plotted characteristics. The phase noise, and Allen Derivation defines different grades of the OCXO. Audio Note Silver Solder Duelund AC0.4 Silver Premium Audio Cable (Silver in Cotton / Oil impregnated) (Handmade in Denmark) (Internel DC cable only) All Giesemann OCXO Modification hand made in Hong Kong with Flagship Weller WX2 Solder Station & WHA 3000P Hot Air Station & Weller WBHS PSB Holder (Made in Germany) AfterDark. Giesemann OCXO Optimised for 25Mhz Ultra Precision Clock Modules (UPCM) for DELA S100 Giesemann OCXO Level selection value The OCXO installed in the product can calibrate the products used in industrial equipment for a long time, and use equipment with good characteristics. In order to optimally select the audio clock, we comprehensively evaluate with Symmetricom Flagship 5125A to analysis the phase noise characteristics and short-term stability (Allen dispersion) that can be determinate the OCXO grading accordingly. The OCXO installed in this product uses a stable OCXO unit that has been calibrated for several months. In order to make the best choice of OCXO. We are conducting a comprehensive evaluation of phase noise characteristics and short-term stability (Allen dispersion) during detailed inspection. The final product will final measured and fine tuned with Keysight 53220A with reference to Atomic Clock , GPSDO. Quality of OCXO is determined by Phase Noise at 1Hz / at 10Hz Phase noise: -119 to -113 dBc / Hz or lower at 1 Hz offset (Grades) -137 dBc / Hz or lower at 10 Hz offset GRADE Phase Noise@ 10Hz Phase Noise@ 1Hz PRINCE -131 -100 QUEEN -132 -103 KING -134 -107 Emperor Signature -138 -110 Emperor Signature SE -139 -112 Emperor CROWN -140 -113 Emperor CROWN SE -140 -114 Emperor DOUBLE CROWN -141 -117 Emperor TRIPLE CROWN -142 -118 Emperor Giesemann -143 -120 Emperor Giesemann EVA -145 -121 Allan variance short-term stability reference value [Emperor Giesemann EVA]TAU = 1sec 2.50E-13 or less(0.00025ppb / s) [Emperor Giesemann] TAU = 1sec 2.78E-13 or less(0.00028ppb / s) [Emperor Triple Crown] TAU = 1sec 3.8E-13 or less(0.00038ppb / s) Giesemann OCXO Modules Technical Specification: Ultra-low phase noise OCXO 25 Mhz Oscillator Output: 25 MHz x 1 system, square wave Output impedance: 75 ohm External DC power supply: 12V 1A 2 years free maintenance warranty Design and specifications are subject to change without notice Made in Hong Kong Dual SFP Port for Optical Isolation for Cascade of DELA S100 Specification: Equipped with 4 100Mbps ports, 4 1000Mbps ports and 2 SFPs (small general-purpose ports supporting optical fiber, etc.) All 4 ports of 100Mbps (No. 1-4) and 1 port of 1000Mbps (No. 8) are priority ports Audio equipment is recommended to connect to 100Mbps Turn off the status display LED of each port with one key to eliminate the effect of flicker Power supply with large capacity capacitor bank board similar to N1 / 3 The chassis is made of 2mm thick high rigid steel plate Half size, compact and easy to install Made in Japan S100-B-J Dimension: 215 × 61 × 270 mm Weight: About 2.5kg 100Mbps LAN x 4 (No.1~4) 1000Mbps LAN x 4 (No.5~8, No.8, SFP and common use, SFP priority)SFP x 2 (No.8~9) Power supply: DC12V (SMPS is included) Amp: Goldmund 27+ EVO Preamp, Goldmund 29M Power Amp, Goldmund AC-Curator DAC: CH Precision C1.1 Digital Convertor, Studer D19 DAC, Wadia 2000 DAC Digital: Mutec MC3-USB, AfterDark. Giesemann OCXO 10M Master Clock Giesemann EVA Playback: Goldmund PH3 Phono Amp, Linn LP12, Studer A807 VU MKII Open Reel Network Switch: AFTERDARK. PROJECT CLAYX BUFFALO BS-GS2016 CASCADE X GIESEMANN OCXO BLACK MODERNIZE EDITION x Farad Super3 LPS Dealer: UpTone Audio, Gustard, Farad Power Supply, Cybershaft, Thixar, DELA Link to comment
Maragoo Posted February 23, 2022 Share Posted February 23, 2022 Hi As Etherregen is no longer available for ordering, how will your modified Dela S100 compaired to combination of ER & Afterdark Clock perform soundwise? Also size of DC plug is used on your Dela S100 for the 12V LPSU? I'm very surprised that there wasn't any feedback so far for this unit. Best regards Rolf Link to comment
AfterDark. Posted February 23, 2022 Author Share Posted February 23, 2022 Hi Rolf, Thanks for your message. We used to have EtherREGEN, and upgrade with the modified DELA S100, and Buffalo BS-2016 when we found this switch is much amazing for use it in HQPlayer and Roon. We are quite confident that will you be suprised when you upgrade to stock DELA S100, the sound is much balanced, smooth, and music flow is much better, The modified DELA S100 will be more advancement with upgrades with internal Gieseman OCXO, carbon fibers, upgrades internal DC cables, using more natural sound Audio Capacitor from Floyt Germany. The DC plug is on 2.1mm and can works plug and play with our Black Modernize LPS. For Buffalo GS-2016, it shares with same motherboard with DELA S100. The latest version we developed this year, could be accepting external 10M Master Reference Clock signal, so customer can upgrade the sounding with their external clock. This is the best combo in less cost when compared. https://www.adark.co/collections/project-giesemann-ocxo/products/afterdark-project-clayx-buffalo-bs-gs2016-cascade-x-10mhz-master-clock-input-module-black-modernize-edition Thanks and have a nice day. Best Regards, Adrian AfterDark. Amp: Goldmund 27+ EVO Preamp, Goldmund 29M Power Amp, Goldmund AC-Curator DAC: CH Precision C1.1 Digital Convertor, Studer D19 DAC, Wadia 2000 DAC Digital: Mutec MC3-USB, AfterDark. Giesemann OCXO 10M Master Clock Giesemann EVA Playback: Goldmund PH3 Phono Amp, Linn LP12, Studer A807 VU MKII Open Reel Network Switch: AFTERDARK. PROJECT CLAYX BUFFALO BS-GS2016 CASCADE X GIESEMANN OCXO BLACK MODERNIZE EDITION x Farad Super3 LPS Dealer: UpTone Audio, Gustard, Farad Power Supply, Cybershaft, Thixar, DELA Link to comment
AfterDark. Posted March 21, 2022 Author Share Posted March 21, 2022 AfterDark. received some customer request to modify the existing DELA S100 / Melco S100 to perform full upgrades and OCXO optimised. For Audiophiles who wants to unlock the performance on audio gear. We loves to perform the modify service called "The Project ClayX" to enhance the Audio Performance. The Project ClayX is always driven by demands on customers, who requires higest performance by upgrades the internal parts, For more details, please feel free to contact AfterDark. via e-mail: [email protected] Amp: Goldmund 27+ EVO Preamp, Goldmund 29M Power Amp, Goldmund AC-Curator DAC: CH Precision C1.1 Digital Convertor, Studer D19 DAC, Wadia 2000 DAC Digital: Mutec MC3-USB, AfterDark. Giesemann OCXO 10M Master Clock Giesemann EVA Playback: Goldmund PH3 Phono Amp, Linn LP12, Studer A807 VU MKII Open Reel Network Switch: AFTERDARK. PROJECT CLAYX BUFFALO BS-GS2016 CASCADE X GIESEMANN OCXO BLACK MODERNIZE EDITION x Farad Super3 LPS Dealer: UpTone Audio, Gustard, Farad Power Supply, Cybershaft, Thixar, DELA Link to comment
Clive101 Posted August 11, 2022 Share Posted August 11, 2022 Just pulled the trigger on the Dela S100 "EMPEROR TRIPLE CROWN" Along with the Finisar SPF x 2 and Fiber . A few weeks to wait for delivery. Link to comment
Popular Post Clive101 Posted November 26, 2022 Popular Post Share Posted November 26, 2022 I must admit I took a punt making a purchase of the AfterDark when I first listened, it was far too bright and thought I have made a mistake but after burn in I am very pleased with the result. Currently, I am using a Sean Jacobs DC1 power supply (on loan) so perhaps not the most expensive power supply. Fiber Finistar FTLX 1475D3 BTL moduels with Commscope Fiber cable into the AfterDark. Ethernet to Antipodes Oladra. Using with an Antipodes Oladra I found streaming from Qubuz better SQ than SSD. SSD was better with the AfterDark than without. I found more detail less fatigue, better separation, tighter textured bass, better attack, better timing, sound stage was better defined. It did not make the music more musical (laid back), nor thinner. Next Power supply upgrade to be continued. AfterDark. and Gavin1977 1 1 Link to comment
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now