Jump to content

mantis07

  • Content Count

    86
  • Joined

  • Last visited

Everything posted by mantis07

  1. ahhh. I didn't realize that RAMROOT can be used without selecting either option - it works now ;) Thank you.
  2. Hello, I'm trying to use RAMROOT with Stylus and am having the issue below. I'm using a Ryzen 4800u NUC with 32GB of RAM. Any ideas? Thanks! Tony
  3. Updated to the latest version and Roon sits forever displaying "The new version of Roon you installed requires a database update - this may take longer than usual" - it's been doing this for over an hour. I always get this message when I update Euphony but it usually only takes 10 minutes or so. I do have a large library (400000 songs) but it has never taken this long. Is anyone else experiencing this? I rebooted my Nuc but no difference. Tech support says they "don't know about Roon db update" and to Roon support LOL. I also noticed that if I open Euphony in a web browser (Win10 Chrome, Edge
  4. So, what I figured out was that the unregistered problem started after I disabled the NUC ethernet. When I first tried wireless I still had the ethernet port enabled. Once I enabled it the unregistered went away and wireless worked but now it will not update my Roon library. Roon sees my NAS but newly added music doesn't get added even with a forced rescan. Right now I have it hooked up via ethernet and the library is updating slowly but Qobuz keeps saying I have no network connection. Everytime I turn on or restart Euphony I have to wait 5 min. for Roon to connect. I never had these problems
  5. Hi Guys, I've been following this thread and decided to try out Euphony. I downloaded the trial and installed it on a spare PC. It sounded really good so I decided to get a 7i7DNFE and I purchased a Euphony license. So, on my first install attempt for the new NUC I downloaded Euphony trial and the write to USB failed at around 80%. I tried again on the same stick and it failed again. The installer actually killed my Sandisk USB stick(now it's read only) so I had to use another stick - same thing - another dead stick. Finally it worked on the 3rd stick. What I didn't realize is that when the
  6. Thanks. I figured it out. I didn't realize the top part of the board needed to be connected to the bottom part - its electrically connected via the 4 pins.. I removed it because it was difficult to get to the 3 pins on the bottom board. I was able to upgrade the firmware and am able to play native DSD 512 via an Sotm sms200. I bought the dac used so can't say what difference the mods made sonically. I just got a Singrex SU1 yesterday and am using the hdmi output. I like the dac but also have a Musical Paradise MP-D2 with some nice tubes and Jupiter copper foil caps. Not sure which dac I like b
  7. Hello, I just got one of these and I was trying to upgrade the Amanero Comb0384 firmware but it seems I've killed the USB card. The DA004 has the upgraded USB card and has the level 1 mod by Ric Schultz. It was working fine before I tried to erase it. According to the Amanero instructions about erasing the flash I would short the square pin to the round at position P3 - unplug/replug the USB cable - all this when powered on. Well my card doesn't have P3 - it has J1 and next to it J3 - see attached pic. I assumed J1 on my card would correspond. I have the Win10 drivers installed from LKS. So t
  8. I did try it both ways - with leveling off I get no sound. So no DSD sound is the problem. I'm hoping Roon can figure this out using my logs. thanks
  9. when I toggle it from off it goes blue says yes and single path shows leveling.
  10. Hi, thanks but it is set to off - see pic 4. Tony
  11. Hi, tried all that and no difference. I attached some screen shots. If I click hide volume control in Roon then it plays but converts DSD to PCM 176 - otherwise it plays with no sound(hiss if volume on the amp turned up loud.) Thanks
  12. With JRiver DSD 64 and 128 play fine using the USB B driver. With Roon using the USB B driver DSD works fine too. If I try Roon with the MR (Roonready set to native) I get no sound from DSD although it plays - if I set it to DOP it get converted to PCM 176. I will send Hegel an email. Thank you! Tony
  13. I will try this when I get home from work but what am I looking for? Thanks Tony
  14. I should have mentioned that I'm using Windows 10. Thanks
  15. Does the MR work with the Hegel H360 internal DAC via USB? I'm using Roon and it plays but without sound. The H360 is supposed to support native DSD and I have the MR set to that. Thanks Tony
  16. Jesus, will June delivery buyers of the mRendu get a tracking # and if so when do you anticipate shipping? Thanks Tony
  17. sorry Mike, I had the NA8005 not SA. I didn't read what you asked carefully.
  18. I returned the Marantz months ago but I was able to play DSF and FLAC - I didn't try anything else.
  19. Mine shows firmware v1.11 - when I hit the curved arrow it says it's up to date. What am I missing? Thanks Tony
  20. Mike, I just got an 8005 a few days ago and can play DSD from a USB stick using the front panel. I will try flac tomorrow. Tony
×
×
  • Create New...