NO SOUND - Raspberry Pi (DietPI) - Allo Piano2.1 DAC - NO SOUND

[RAH905]

brand new Allo Piano2.1 DAC 

installed in on Raspberry Pi4.

DietPI and Kodi sees DAC as default audio device.

I'm able to turn up/down volume via Alsamixer, Kodi, etc.

 

however, there is NO-SOUND coming out of these RCA connectors.

Been trying to figure this out since this morning. 

 

Any help will be much appreciated. My Soul will thank you forever.

[Audio_Allo]

On 4/10/2022 at 7:56 AM, RAH905 said:

brand new Allo Piano2.1 DAC 

installed in on Raspberry Pi4.

DietPI and Kodi sees DAC as default audio device.

I'm able to turn up/down volume via Alsamixer, Kodi, etc.

 

however, there is NO-SOUND coming out of these RCA connectors.

Been trying to figure this out since this morning. 

 

Any help will be much appreciated. My Soul will thank you forever.

Can you please login dietpi through ssh and share below command results ,Forwarded PM also please check

 

aplay -l    (Lower case of L)

cat /boot/config.txt

[RAH905]

1 hour ago, Audio_Allo said:

Can you please login dietpi through ssh and share below command results ,Forwarded PM also please check

 

aplay -l    (Lower case of L)

cat /boot/config.txt

@DietPi:~# aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: PianoDACPlus [PianoDACPlus], device 0: PianoDACPlus multicodec-0 [PianoD                       ACPlus multicodec-0]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
@DietPi:~# cat /boot/config.txt
# Docs: https://www.raspberrypi.com/documentation/computers/config_txt.html
# Overlays: https://github.com/raspberrypi/firmware/blob/master/boot/overlays/README

#-------Display---------
# Max allocated framebuffers: Set to "0" in headless mode to reduce memory usage
# - Defaults to "2" on RPi4 and "1" on earlier RPi models
#max_framebuffers=0

# If you get no picture, set the following to "1" to apply most compatible HDMI settings.
#hdmi_safe=1

# Uncomment to adjust the HDMI signal strength if you have interferences, blanking, or no display.
# - Ranges from "0" to "11", use values above "7" only if required, e.g. with very long HDMI cable.
# - Default on first RPi1 A/B is "2", else "5", on RPi4 this setting is ignored.
#config_hdmi_boost=5

# Uncomment if HDMI display is not detected and composite is being outputted.
#hdmi_force_hotplug=1

# Uncomment to disable HDMI even if plugged, e.g. to force composite output.
#hdmi_ignore_hotplug=1

# Uncomment to force a console size. By default it will be display's size minus overscan.
#framebuffer_width=1280
#framebuffer_height=720

# Uncomment to enable SDTV/composite output on RPi4. This has no effect on previous RPi models.
#enable_tvout=1
# SDTV mode
#sdtv_mode=0

# Uncomment to force a specific HDMI mode (this will force VGA).
#hdmi_group=1
#hdmi_mode=1

# Uncomment to force an HDMI mode rather than DVI. This enables HDMI audio in DMT modes.
#hdmi_drive=2

# Set "hdmi_blanking=1" to allow the display going into standby after 10 minutes without input.
# With default value "0", the display shows a blank screen instead, but will not go into standby.
# NB: Some legacy OpenMAX applications (OMXPlayer) cannot wake screens from real standby.
hdmi_blanking=1

# Set to "1" if your display has a black border of unused pixels visible.
disable_overscan=1

# Uncomment the following to adjust overscan.
# Use positive numbers if console goes off screen, and negative if there is too much border.
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# Rotation
#display_hdmi_rotate=0
#lcd_rotate=0

#-------RPi camera module-------
#start_x=1
disable_camera_led=1

#-------GPU memory splits-------
gpu_mem_256=76
gpu_mem_512=76
gpu_mem_1024=76

#-------Boot splash screen------
disable_splash=1

#-------Onboard sound-----------
dtparam=audio=off

#-------I2C-------------
#dtparam=i2c_arm=off
#dtparam=i2c_arm_baudrate=100000

#-------SPI-------------
#dtparam=spi=off

#-------Serial/UART-----
# NB: "enable_uart=1" will enforce "core_freq=250" on RPi models with onboard WiFi.
enable_uart=0

#-------SD card HPD-----
# Comment to enable SD card hot-plug detection, while booting via USB or network.
# NB: This causes constant CPU load and kernel errors when no SD card is inserted.
dtparam=sd_poll_once

#-------Overclock-------
temp_limit=75
initial_turbo=20

#over_voltage=0
#arm_freq=1500
#core_freq=500

#over_voltage_min=0
#arm_freq_min=300
#core_freq_min=250
#sdram_freq_min=400
arm_64bit=1
dtoverlay=disable-wifi
dtoverlay=rpivid-v4l2
dtoverlay=vc4-kms-v3d,cma-512,noaudio
dtoverlay=allo-piano-dac-plus-pcm512x-audio