Rendu Support Thread

[BCRich]

1 hour ago, .Will. said:

Thanks.  DAC doesn't show up at all in Apps / DAC Diagnostics.  Any idea why not?

 

 

Make sure your DAC is powered on and the USB input is selected, then reboot the ultraRendu.

The ultraRendu should now see your DAC.

[BCRich]

Actually the First Eero that is connected to your Modem is the Primary one, it is the one handing out the IP Addresses and is acting as the Router. The others create the Mesh Network. You should be connecting the Modem to the First Eero and from the First Eero to to a switch if you are using one. The other suggestion I have is to Reserve the IP address of each mRendu to ensure there are no IP address conflicts. I am using them in my house and I am pretty sure that when I had both my mRendu and ultraRendu on the Network both were visible in Roon. I unfortunately cannot confirm this as I have since sold the mRendu.

Hope you figure it out.

Good Luck,

Mike   

[BCRich]

Pretty sure you need to enter the IP address into a browser and then configure it to use Roon.

Your SE should appear under Network Devices, select manage and then select apps and then Audio app switcher and from there you should be able to enable Roon Ready. ie. Enable Roon Ready in app Manager and save. I am assuming it uses the Sonicorbiter interface, have never owned an SE.

Hope this helps.

Mike

[BCRich]

1 hour ago, Theobetley said:

So I had a power outage but got all powered up again but I cant get connectivity from my uptone LPS1.2 powered microRendu to my dac. Tried     cycling my pc,      dac, roon and nogo. Any ideas?

Make sure your Dac is powered up and the LPS-1.2 has a green LED before you power up the mRendu, in other words don’t connect the output of the 1.2 to the mR until it’s power led is solid green. Hope that helps.

Mke

[BCRich]

I don’t think a Static IP can be set. I am using an eero network and set up an IP Reservation for my ultraRendu. Never a problem. Sounds like other devices are grabbing the Rendu’s IP, is it disconnecting from your network? I would try the IP Reservation and see what happens.

Good Luck.....

Mike

[BCRich]

Have you enabled Roon Ready for the mR in app switcher on the Sonic Orbiter GUI?

Roon will not see it until you do that.

Stay Safe and Healthy......Mike

[BCRich]

I would try rebooting your network and all associated devices, also close the Roon App and reopen it.....bizarre!

[BCRich]

I would unplug/disconnect everything and reseat the SD Card. Worth a shot, there might be a physical problem based on what it’s doing.

Good Luck.....Mike

[BCRich]

You probably have a problem with your LPS-1.2, I would reach out to Alex.

[BCRich]

I think he said he was using the Uptone supplied one, and if he used that instead of the LPS-1.2 he had no issues.

[BCRich]

39 minutes ago, R1200CL said:

@vortecjr

 

Total download size: 49 M
Downloading Packages:
(1/5): kernel-5.2.17-205.sgc.fc30.armv7hl.rpm 46 kB/s | 17 kB 00:00
(2/5): RoonReady-1.1.38-1.fc30.armv7hl.rpm 60 kB/s | 530 kB 00:08
(3/5): networkaudiod-4.1.1-1.fc30.armv7hl.rpm 40 kB/s | 266 kB 00:06
(4/5): kernel-modules-5.2.17-205.sgc.fc30.armv7 60 kB/s | 20 MB 05:36
[MIRROR] kernel-core-5.2.17-205.sgc.fc30.armv7hl.rpm: Downloading successful, but checksum doesn't match. Calculated: 4cae44a449887f151446abf2ef85b9511122195376056e2aaef1e9c7d63a5995(sha256) Expected: 8417639b8833abb03a2b4d2f346a677e7ddaeab2c9b7334dae4ed7d0760f2379(sha256)
(5/5): kernel-core-5.2.17-205.sgc.fc30.armv7hl. 33 kB/s | 29 MB 15:02
[Errno 2] No such file or directory: '/var/cache/dnf/download_lock.pid'
The downloaded packages were saved in cache until the next successful transaction.
You can remove cached packages by executing 'dnf clean packages'.
04/25/2020 10:25:49 - Error: dnf update failed. Check error messages and try to fix the problem.
Back to main menu

 

Any comment regarding the above ?

(you closed the other thread)

I would run the update again, I remember when 2.8 became available executing the update twice seemed to clear up issues. When was the last time you ran an update?

[BCRich]

Is the OpticalRendu up to date? I remember this was an issue when the 2.8 version of Sonicorbiter OS came out. You had to update the unit twice, after that it was ok. I was experiencing the same issue, it would just shut down.

I have the Power Supply that Barrows builds, you have the same one? Not the SGC one....

Hope this helps.....

Mike