stefano_mbp Posted February 6, 2020 Share Posted February 6, 2020 Hi, here the same problem reported by franz159 I’m trying to install your sw to test it but every time, after some configuration, RPI do not reboot and I must reflash the card starting from 0 .... My configuration should be quite simple: configure static IP address enable mpd enable upmpdcli assign a usb dac but something go wrong and pi do not reboot .... every time, with different microSD It seems that something breaks the sw, during reboot I can see just few green flashes then nothing at all ... died I do not have any wlan configured in my network my rpi is a RPI 4/4Gb (ver. 1.2) and the dac is a Khadas Tone Board thank you stefano Stefano My audio system Link to comment
stefano_mbp Posted February 7, 2020 Share Posted February 7, 2020 for now I prefer to enjoy the sound of this sw which seems really amazing to me I will try other configuration options in the coming days for now mpd + upmpdcli + mpd bit perfect looks really ... perfect thanks again for your excellent support Stefano Stefano My audio system Link to comment
stefano_mbp Posted February 8, 2020 Share Posted February 8, 2020 two more problems after gp-update this morning 1) if I enable mpd and upmpdcli the web interface crashes but it is possible to reach rpi with ssh and the restart the web interface 2) if I disable HDMI it is impossible to reboot ... then a reflag is needed Stefano My audio system Link to comment
stefano_mbp Posted February 9, 2020 Share Posted February 9, 2020 Big thanks to @antonellocaroli for his fantastic support on a boot problem due to a network configuration .... directly on my system with a remote session ... 👍 Stefano My audio system Link to comment
stefano_mbp Posted February 17, 2020 Share Posted February 17, 2020 @antonellocaroli .... finally everything working fine here .... but ... using mpd/upmpdcli is there any way to define to use DoP (dsd over pcm) instead of native dsd (like “-D” in Squeezelite)? thank you Stefano My audio system Link to comment
stefano_mbp Posted February 17, 2020 Share Posted February 17, 2020 26 minutes ago, antonellocaroli said: you have to put this <dop "yes"> in audio_output { ..... .... ... dop "yes" } https://thepenguin.eu/2017-12-22-mpd-and-dsd-files/ ... very easy indeed ... it works ! ... and now ... Music! thank you Stefano My audio system Link to comment
stefano_mbp Posted February 23, 2020 Share Posted February 23, 2020 5 hours ago, antonellocaroli said: Rpi4 Update -updated the entire system -updated firmware and EEPROM firmware (vl805) (temperature should be lower now) -updated uhubctl -added hub-ctrl.c -fix remove audio software @nbpf Web-interface: -added firmware update function -added cpu-temp real time (bcmstat) -added GP-version update (from this version on, it should no longer be necessary to refresh the SD to update the version) Great job @antonellocaroli ... rpi4 v.1.1 is running 3/4 °C less than before ... the firmware update is effective.... not yet tested on a rpi4 v.1.2 but it runs already colder ... 43° C in a Flirc alluminium case ... and the sound is ... wonderful Stefano My audio system Link to comment
stefano_mbp Posted March 9, 2020 Share Posted March 9, 2020 Hello @antonellocaroli just upgraded to version 2.11 on rpi4 using the web interface and everything is ok but ... the functions Player C, D, E, F are not working anymore, if I select one of them I receive the error “Failed to load script info. Try to reload the page. Error message: Failed to connect to the server” Stefano My audio system Link to comment
stefano_mbp Posted March 9, 2020 Share Posted March 9, 2020 I did but nothing changed Stefano My audio system Link to comment
stefano_mbp Posted March 27, 2020 Share Posted March 27, 2020 ... I do not use Spotify... ... in GentooPlayer put to “enable” MPD and upmpdcli from the Player.A menu ... JRiver should then be able to see it antonellocaroli 1 Stefano My audio system Link to comment
stefano_mbp Posted March 27, 2020 Share Posted March 27, 2020 @zacho .... as I explained in my previous post .... follow the instructions and Jriver will find it antonellocaroli 1 Stefano My audio system Link to comment
stefano_mbp Posted March 30, 2020 Share Posted March 30, 2020 @antonellocaroli hello, just tried to update version to 2.12 gave gp-update command using web interface then the web interface is gone .... tried to restart the web interface in terminal without success still possible to use terminal what to do? thank you Stefano My audio system Link to comment
stefano_mbp Posted March 30, 2020 Share Posted March 30, 2020 .... all the above where done using a tablet (iPad) just checked on Mac/Safari and is working .... but still no more web interface on iPad/Safari Stefano My audio system Link to comment
stefano_mbp Posted March 30, 2020 Share Posted March 30, 2020 .... update is ok and, clearing iPad/Safari cache, the web interface on iPad/Safari is up and running again ... so much ado for nothing .... thank you! Stefano My audio system Link to comment
stefano_mbp Posted March 30, 2020 Share Posted March 30, 2020 @antonellocaroli ... the cherry on the cake ... I added the GP icon .... antonellocaroli 1 Stefano My audio system Link to comment
stefano_mbp Posted March 31, 2020 Share Posted March 31, 2020 6 hours ago, Groucho said: Hi Stefano, this screenshot is related to...? Thanks Hello Groucho it is Lumïn app, I configured upmpdcli.conf file of GentooPlayer to show the logo in the control point as you can see on the left of my two gp renderers *GP-Studio and *GP-P1S antonellocaroli 1 Stefano My audio system Link to comment
stefano_mbp Posted April 1, 2020 Share Posted April 1, 2020 @DomieMic65 you actually have two options the first is to have Bubbleupnpserver installed anywhere in your network, this is my option even if I don’t use the one from GentooPlayer the second is to change the lumincompat parameter to 1 in upmpdcli.conf in GentooPlayer, but you loose the possibility to login to streaming services as Qobuz and Tidal here you can find the upmpdcli user guide https://www.lesbonscomptes.com/upmpdcli/releases.html https://www.lesbonscomptes.com/upmpdcli/upmpdcli-manual.html#UPMPDCLI-RENDERER-FORMATS clipper 1 Stefano My audio system Link to comment
stefano_mbp Posted April 2, 2020 Share Posted April 2, 2020 37 minutes ago, antonellocaroli said: you have to activate and configure bubbleupnp. and comment in the configuration file of upmpdcli lumincompat .... you are right .... as I told before, my configuration is to use Bubbleupnpserver and didn’t realized that, due to a recent update, Lumïn app is not working good anymore using the option to use the lumincompat parameter. ... sorry for the misunderstanding... DomieMic65 1 Stefano My audio system Link to comment
stefano_mbp Posted April 2, 2020 Share Posted April 2, 2020 2 minutes ago, DomieMic65 said: bubleupnp must be activated and configured in my player rpi or it can be done and on the server? thank you! you can install bubbleupnpserver where you like, I installed it on my NUC on which is installed Minimserver too to configure it after the installation type in your web-browser server-ip-address:58050 DomieMic65 1 Stefano My audio system Link to comment
stefano_mbp Posted April 3, 2020 Share Posted April 3, 2020 @guilders try to clear the web browser cache antonellocaroli 1 Stefano My audio system Link to comment
stefano_mbp Posted April 10, 2020 Share Posted April 10, 2020 @luisma maybe a silly question: is your netmask 255.255.0.0 over all your network? Stefano My audio system Link to comment
stefano_mbp Posted April 10, 2020 Share Posted April 10, 2020 I could mistake but with /24 your two subsets... subnets.... are segregated, they do not communicate with each other Stefano My audio system Link to comment
stefano_mbp Posted April 10, 2020 Share Posted April 10, 2020 More sure now .... I am not used to /xx notation ... /24 means all the addresses inside a single subnet, that’s to say 255 addresses in 192.168.95 255 addresses in 192.168.96 but the two subnets do not communicate with each other, you need to define a different netmask and it should be 255.255.0.0, in this way your two segment will communicate each other Stefano My audio system Link to comment
stefano_mbp Posted April 10, 2020 Share Posted April 10, 2020 .... network management is sometimes a hard topic ... the nuc having the two legs on different subnets can be misleading, all the network things must know where to send a packet and if the netmask is too narrow the packets are lost. cannot say why it was working before but this is what the network management theory says. try it ... we all have plenty of time in these days .... Stefano My audio system Link to comment
stefano_mbp Posted April 10, 2020 Share Posted April 10, 2020 Just now, luisma said: Or could be something off on the IPv6 implementation as well. Cannot say anything about ipv6, sorry Stefano My audio system Link to comment
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now