Mola Mola Pre/dac review compared to DAVE dac

[toetapaudio]

Links:

 

Specifications:

https://www.mola-mola.nl/Maku.html

 

https://www.mola-mola.nl/DAC.html

 

Some tech from the designer Bruno Putzeys explaining to me some of the aspects of the dac design:

 

The upsampler and modulator are written in software. The upsampler is an asynchronous sample rate converter. You can also buy chips that do that but they only come with "just good enough" filter responses and neither do they have a particularly narrow PLL bandwidth so there was no alternative left but build one from the ground up. The choice for asynchronous vs using multiple clock crystals was made because you can't make a tuneable oscillator with the extremely stable SC cut crystal that MM use.

 

Far from being hard coded, the entire thing is completely software defined. OTOH the user has no say in what type of filter it uses, it being felt that allowing users to toy with it was a gimmick, since for every input rate there can only be one filter setting that is least audible (the filters change with input rate and format). It follows that any one might add just for the sake of "giving users a choice" would be more audible.

 

The modulator is PWM and is based on a scheme invented in 2004 to generate noise shaped PWM. It should be noted that it's not an n-bit noise shaper followed by a conversion to PWM but the PWM is noise shaped directly. Of course, from an information perspective we're still looking at the equivalent of 5 bits at 3.125 MHz however you want to look at it. The gory details are in https://www.hypex.nl/img/upload/doc/an_wp/WP_AES120BP_Simple_ultralow_distortion_digital_PWM.pdf

What sets this type of PWM aside from ordinary 1-bit sigmadelta is that it is inherently free from intersymbol interference. If you reproduce a 1-bit signal using a switching circuit whose rising and falling edges aren't exactly symmetrical you get a distortion component equal to the number of 1/0 transitions per second, which varies with the signal and which has tone like components. With the single-edged PWM conversion the number of transitions per second is constant and only one of the two edges encodes a signal so the same rising/falling asymmetry would cause nothing worse than a tiny amount of DC offset. This observation was first made by Peter Craven in 1993, who was then trying to design a DAC for B&W and published a way of generating such a signal. So if you are looking for a historical precedent for using PWM in a DAC, that is the closest you'll get. If you compare Craven's paper (http://www.aes.org/e-lib/browse.cfm?elib=7001 ) with the one linked above you can see the new method is significantly more straightforward and has lower distortion.

 

The FIR trick is this: if you generate a clocked PWM signal with a period of N clock cycles, and you run that through a FIR filter with N equal valued coefficients, the output of that FIR filter is simply the total number of ones over the past full cycle. This removes the PWM switching frequency and some shaped noise from the output signal, making life easier on the analogue filter that follows. The resistors need not be matched since each tap sees the complete signal. A mismatch only slightly affects the attenuation of the 3.125MHz component. This is why FIR DACs are used. They have been around in some form or other since the mid 90's. I'm not sure about other commercially available PWM based FIR DACs though.

 

Quotes from two recent reviews (not available as links at this time)

 

Hi-Fi Choice: 

 

Makua Pre/DAC: " Like: Spacious, open sound, build, excellent app control. Dislike: Nothing. We say: Super versatile and capable modern preamp.

 

Hi-Fi News:

 

"....its aforementioned unflappability at high volumes and smoothness from bottom to top- it''s another facet that's part of its big, confident yet calm character."

 

"Bass was lithe and tuneful, the mid band delicate and satisfyingly three-dimensional, while treble has a wonderful satiny texture to it."

 

Test set up:

AQVOX switch with King Rex dc ps in port 1 out port 8 and grounding wire , AQVOX and Vovox Ethernet cables, fidata network work server, Vovox USB to dac, Lumin S1 using digital out, Mola Mola Makua preamp with dac module, Mola Mola Kaluga mono block amplifiers, Hi Diamond XLR 3 interconnects, Boenicke W11 with external Bybee speaker bullets, Hi Diamond 7 speakers cables, separate mains spurs to each component terminated in IEC plugs and dedicated consumer unit, Bybee signal enhancers under each individual component including the hub and switch, SteinMusic Harmonizers with blue suns and diamonds, Bybee signal enhancers in the room at various points, room 3.5m. x. 7m x 2.5m.

 

Comparisons: Chord DAVE, Lumin S1 built in dac, Benchmark DAC2, SST with dac module.

 

TBC

[toetapaudio]

2 minutes ago, jaspal kallar said:

Thanks,  interesting.

 

I know Bruno Putzeys  is one of the kii (yes pun intended) people behind the Kii Three speaker. 

 

I was curious if he incorporated some of the Dac technology from the Mola Mola Dac/Pre into the Kii Three speaker (system).  These speakers are on my radar. 

 

 

Kii's at £10,000 pair offer great value at that price point with everything built in, but ultimately Mola Mola Makua/Kaluga and good passive speakers will better them for SQ, but of course costs more.

 

I can't answer how much of the Mola tech there is in the Kii's but there must be some.

[toetapaudio]

Review continued.

 

Ease of use.

 

There are three options to use the Mola Mola remotely plus manual operation. The remotes are the supplied Apple controller, the cnc machined Mola Mola handset (optional extra) and the Mola Mola app using an iPad. There are six presets that can be selected remotely, each one can be set up for whatever application you need. If a phono stage is included (at an extra cost) you could for example set up one for MM cartridges and another for MC cartridges, each with their own R, C, Gain and Equalisation. The volume can be controlled from the remotes or the knob on the front and is a relay analogue device.

 

The rear has IEC for power, and six pairs of balanced (XLR) and unbalanced (phono) inputs with a switch to select. The selection can also be made remotely. Also there are digital inputs (if the dac module is included), one USB type B, and one AES/EBU plus LAN for future use.

 

Comparisons.

 

Price points: Benchmark DAC 3 (£2350), SST pre/dac (£4200), Lumin S1 streamer/dac (£8,500), Chord DAVE dac (£8,500), Mola Mola pre/dac (£11,000).

 

I have been using the Mola Mola Makua pre/dac for around 6 months and have had the opportunity of comparing it with the above. My reference before taking on Mola Mola was the built in dac in the Lumin S1. The transport only version, the U1, is £4,500, so the dac in the S1 is worth around £4,000. The sound of the S1 was far more open and natural sounding and musically engaging compared to the Benchmark and SST. The Benchmark was detailed but over bright, the SST a bit constricted but better balanced and smoother, more natural than the DAC3. The S1 was clearly superior to both. At this time I had tried the S1 with both the SST as preamp and also direct using the Lumin's app to control volume. I preferred the sound when used direct.

 

The Mola Mola pre/dac took the sound to new levels of sonic delights. The sound stage expanded, there was more texture, notes lasted longer, smoother, more open and natural, musical enjoyment increased and I was tapping my toes more often.  And they weren't even run in yet. The sound just got better and better as time went on. The sound became more dynamic and even more musically involving and maybe there is even more to come.

 

Comparison with the Chord DAVE to follow.

[toetapaudio]

Mola Mola vs Chord Dave

 

I was very pleased with the sound quality of the Mola Mola but I was curious to know how the Mola Mola compared to the Chord Dave, obviously a very good DAC that had so many positive user reviews in the forums. I also read a report of a Chinese Hi-Fi Club that had compared the Dave with some other top performing DAC’s including some costing much more. The blind test results were:

 

1. Chord DAVE
2. Lavry Quintessence DA-N5
3. Merging NADAC
4. dCS Vivaldi DAC
5. TOTALDAC D1-DUAL
6. Lavry DA2002
7. SCHIIT YGGDRASIL
8. AQUA La Scala

 

I had been aware of a private test of a Mola Mola DAC vs Nagra DAC with the former coming out on top. Also I was told of another comparison with the Dave DAC, in which the five people present were split 2/3 in favour of Mola Mola.

I started the comparison with the Dave connected directly to the two mono Kaluga power amps. The interconnect was a HiDiamond XLR3, a revealing and musical interconnect in my opinion. Inputs were fidata network audio server through usb and Lumin S1 digital out through AES. All listening tests were through Boenicke W11 speakers.

 

As high-lighted by many posters in the forums, the Dave was a smooth, open, refined and naturally balanced performer. Many types of music were used in our comparison: acoustic jazz, rock, opera, acoustic blues, classical and percussion. We listened to a number of tracks and then repeated the same series of tracks with the Mola Mola in place. Both DAC’s were really good of course, PRAT was very close, coherence, transparency and information equally as good. But, there were differences in terms of musicality, the Mola Mola being more musically involving. On all forms of music the Mola Mola was just a bit more engaging and toetapping. It was the same “painting”, the Dave was in muted colours and the Mola Mola in more lit up tones. 

 

Obviously the next thing to try was the Dave into the Mola Mola as a preamp with Dave’s digital volume control muted. I have read that a number of users prefer the sound with Dave connected via a preamp. Some, like @romaz, would disagree that Dave with a preamp is necessary and would prefer to use the Dave direct, even without a power amp. The dac direct to speakers set-up I didn’t try because, one, it didn’t occur to me at the time and secondly I wouldn’t have had the cables prepared to make that test. In our system and to us, the Dave benefited by using it with the Mola Mola as preamp. @romaz would argue that that is just putting another unnecessary layer behind the dac. To my ears, when connected to the Mola Mola as a preamp, the Dave gained in more inner musical energy, texture and colour and got much closer to what I preferred about the Mola Mola.

 

There are other considerations of course. Cost for one thing. The Mola being the more pricey set up being around £11,000 as a pre/dac vs £8,500 for the dac only Dave. The Dave also enables the user to use headphones directly connected to the dac, a big plus for head-fi fans. The upcoming stand alone DAC from Mola Mola I hope has the same facility, but this is not confirmed yet. Price point should be comparable with the Dave and the Mola Mola will have Roon end points built in. If you need a top flight preamp (because you are also using a turntable for example) then the Mola Mola makes a lot of sense as a one box solution that can later be updated with other facilities (such as Roon) when available.

I hope this helps.

[toetapaudio]

avtech_awards_17_Mola_Reprint-LOW.pdf

[toetapaudio]

@johndoe21ro what do you want to know?

[toetapaudio]

@johndoe21ro, apart from Dave, I have compared the Mola Mola DAC/pre to the inbuilt DAC of the Lumin S1 and the SST Theobe DAC/pre. In both cases the Mola Mola was superior, being more open and naturally balanced, with greater musicality, giving you a better sense of how the instruments are being played, more extended and cleaner bass, improved transparency and transients. The other three are very good in their own right and price group but the Mola Mola is outright a better DAC. Hope this helps. You really need to borrow one and try it at home.

[toetapaudio]

7 hours ago, yyz said:

Is the Makua's implementation of Tone controls released. I keep reading that this unit has Tone controls but not sure if this is a yet to be released add-on board or Tone controls already exists, implemented via the software app.

 

We are a Mola Mola dealer. The command list for the Makua includes treble and bass settings from +/- 7.

 

Any further questions please let me know.

[toetapaudio]

Hi Presmara, thanks for your interesting comparisons and welcome to the forum. I’m glad you are liking the Mola Mola Makua pre/dac, we haven’t heard a better dac at any price with comparisons made to the Chord DAVE and Nagra dac’s among others.

I see you are using the Antipodes 3, so USB cables would be important to you. My recommendation without hesitation is the Sablon Reserva Elite USB. Absolutely stunning with the Mola Mola.

 

Another absolute must have is the Sablon power cable, just staggering with the Makua. This cable is probably the biggest single upgrade I have ever experienced. Feel free to PM me for further details and tips on setting up the Makua for best performance if you wish.

[toetapaudio]

We are talking £16k for the Chord combo Vs £9k for the Tambaqui. IMO you would be better off with the Mola Mola DAC plus top flight Sablon Reserva USB and power cable (£2k approx) and have nearly enough left over to buy a fidata server (£6k). The fidata is a very special server and is among the very best regardless of price and should be compared with the likes of SMG and MP64, not Innuos or NB.

[toetapaudio]

I was referring to @ George Flush’s request.

[toetapaudio]

On 28/04/2018 at 4:33 PM, HeeBroG said:

 

Hi toetapaudio,

Can the Mola Mola Pre/DAC drive high efficiency speakers directly?

 

@HeeBroG, I have gone back to the factory with that question and expect an answer shortly. We have not tried ourselves. What speakers did you have in mind and what is their efficiency please? What country are you living in?

[toetapaudio]

@HeeBroG

 

This is the distributors take, Bruno’s comments I will need to wait for:

 

Using the Tambaqui in this way is not recommended by Mola Mola, even with speakers with 105dB efficiency and with impedance boosters.
The benefit of not having the additional circuitry of a power amplifier in the signal path is offset by the compromised performance of using an
impedance booster and the limited speakers available with high enough efficiency ratings. We would definitely recommend using the Tambaqui
in conjunction with a pair of Kaluga mono power amplifiers. This will then drive virtually any high performance loudspeaker and offer significantly
better performance.

Are owners of Dave using the headphone output as the feed to loudspeakers or the preamp outs? If they are using the balanced or unbalanced
pre amp outputs, then the spec of Tambaqui should be virtually identical as these are reasonably uniform voltage outputs.

 

@HeeBroG, your thoughts please.
 

 

 

[toetapaudio]

@john925, if you are in the UK I can arrange for you to hear a Makua. The Makua is a very versatile pre-amp and is very neutral sounding. It can be fitted with phono or dac modules, as required. Specific settings can be applied for different types of cartridges, so for example if you had a turntable with several pick-up arms each fitted with different cartridges, each one can be set-up individually for optimal performance. Volume control and input selection can be made from your tablet using the app or the remote supplied. Manual selection is also available. Inputs are XLR and RCA. Digital inputs if specified are USB and AES. Outputs are XLR and RCA.

 

Fit and finish are immaculate, the top and front panel machined from one piece. The Makua is supplied in a solid flight case with a comprehensive set-up manual.

 

As regards comparison with the Audio Research Reference SE, this is something we haven’t made but we and others have compared the Makua with other pre/dac’s and the Makua has always been preferred. Apart from my Dave comparison (see above) favourable comparisons have been made against dCS, SST, Weiss, Playback Designs, Nagra etc.

 

If you have any specific questions please ask.

[toetapaudio]

@Marcel073, thanks for your input. It’s great to hear from people who are liking Mola Mola.

 

Vivid and Mola Mola are a great combination, which I’ve heard. I can also highly recommend the Boenicke speaker range which we demonstrate with the Mola Mola dac and power amps, for really good compatibility.

 

@barrows, great comments and insight.

 

Mola Mola Kaluga’s can be compared with the best Class A designs imo. We know of somebody who has switched from a £50k Swiss made class A design to £10k Kaluga’s and was very happy with his decision.

 

As regards where the Benchmark ABH2 stands when we tried it was on par with the cheaper Nord class D amps, no way as good as the SST Son of Ampzilla 2 and all of them not in the same league as the Mola Mola Kaluga’s.

[toetapaudio]

@Hyperion, that’s our system right there. Nice photo. 

 

We use the Fidata server and Sablon cables with SteinMusic Harmonizers. Plus a stack of Bybee Signal Enhancers on the mains consumer unit, switch and hub. Calms things down dramatically and makes a HUGH improvement given time. We are going to experiment with other mains calming techniques in the near future which I’m very hopeful about. Attention to mains quality is a whole subject in itself and deserves our utmost attention.

 

@Marcel073 it’s a pleasure dealing well with Sven, really nice guy and he knows his stuff. Same with Bruno Putzeys.

[toetapaudio]

Oh, I forgot to mention we also use toetapaudio custom built isolation furniture which is hung on silk threads. All solid wood construction. 

[toetapaudio]

@rickca, we haven’t tried the Ayre QX-5. We have tried against the Chord Dave and others have commentated that they rate the MM compared to Nagra and dCS. Not sure if that helps? Maybe you could borrow a Tambaqui?

[toetapaudio]

@rickca, I believe they have lent out before. Let us know how it goes.

[toetapaudio]

@Marcel073, two products I can recommend you take a look at:

 

Fidata server (for music downloaded). 1 or 2 TB storage.

 

and/or

 

Lumin U1 or U1 mini renderer (for streaming). 

[toetapaudio]

@Marcel073, the new Lumin U1 mini is £1,695.00. Great value I believe.

 

The Fidata is £6k, but is extremely good and we use it as our reference. The only others that might compare are the Netherlands brands Pink Faun, Evo 432 and SMG,  all of which cost more.

 

@jtwrace, are you in the U.K.? We can lend you one to try if you are.

[toetapaudio]

Well we are waiting for one but we use the Makua Pre/Dac atm. If you are a using a turntable as well as digital, this is the one to go for.